Who Owns the Gas Monitor Before Confined Space Entry?
Here’s a scenario that plays out on worksites all the time. The host employer assumes the incoming crew has a gas monitor. The crew assumes the host has already tested the space. And then someone signs the entry permit, and everyone walks away thinking atmospheric testing is someone else's problem. That blurry handover is exactly where confined space gas testing goes wrong.
This post is here to clear that up. We're going to walk through who actually owns the gas monitor before anyone steps into a confined space, and what the pre-entry sequence should look like so it isn't left to chance. You'll get across what WA law requires before testing even starts, who the competent person is, how host employer and incoming crew duties split, and why calibration and bump testing matter before you trust a reading. We'll also cover the step-by-step pre-entry sequence, the documentation that proves ownership, where training fits in, and a quick handover checklist you can use on your next job.
If you've ever stood at the edge of a space wondering whose job it is to press the button, this one's for you.
Gas Testing Is the Handover Step Nobody Signs For
On most WA sites, the host employer owns the space and the incoming crew owns the entry. Somewhere between those two facts sits the gas test, and too often both sides quietly assume the other has already run it.
That assumption is why you're here. You don't need another definition of a confined space. You need to know who holds the monitor, who runs the test, and who signs it off.
Ownership becomes real with three things: a named competent person, a calibrated and bump tested gas monitor, and a documented pre-entry sequence. Miss any one and the handover is just a conversation. When it is assumed, you get readings taken by whoever is closest, no tester's name on the record, and no clear accountability if conditions change mid-shift.
This article diagnoses that handover gap, then walks through a step by step confined space gas monitoring sequence that names the responsible role at every stage. Read Why Gas Testing in Confined Spaces Is Non-Negotiable in WA for the bigger picture.
What WA Law Actually Requires Before Anyone Tests
Before we sort out who holds the monitor, here is the legal ground you are standing on. The Work Health and Safety Act 2020 (WA) puts a primary duty of care on every PCBU to keep workers and others safe, so far as is reasonably practicable. Specific confined space duties then sit in the Work Health and Safety (General) Regulations 2022 (WA). Our guide to the five core confined space obligations every WA employer must meet unpacks those.
The approved Code of Practice: Confined spaces is approved under section 274 of the Act. It is aimed at the PCBU, and courts can treat it as evidence of what is known about the hazard and its controls. WorkSafe WA, within the Department of Local Government, Industry Regulation and Safety, enforces it.
Watch the wording. Must, requires and mandatory signal legal duties. Should is recommended practice. Do not upgrade a should in your SWMS, and do not soften a must.
One scoping note. AS/NZS 60079.29.1:2017 covers flammable gas detector performance only. It is not the standard for all atmospheric testing.
Who Is the Competent Person for Confined Space and Gas Testing?
A sentry controls entry and exit and monitors everyone inside. That is not the gas tester's job unless your site says it is. Here's the gap: host procedures reviewed for this article require a nominated delegate and a sentry, but they don't name who runs atmospheric testing. Your SWMS has to close that.
Name the person, their position and their authority in the JHA or SWMS. Spell out monitor selection, running the test, interpreting results and authorising entry. For competence, record current training, hands-on time with that specific confined space gas monitor, and knowledge of the hazards in that particular space. That's the evidence a supervisor can check.
A simple who does what table in the SWMS helps: host employer, incoming crew supervisor, competent tester, sentry and standby rescue. It also makes confined space gas monitoring ownership scannable. For training that supports the tester, see why combining confined space, gas testing, and heights training makes sense.
Host Employer vs Incoming Crew: Splitting the Duty
You have named the tester, so now lock the split between parties. Under the Work Health and Safety Act 2020 (WA), a host employer and an incoming contractor can both be PCBUs for the same work, so their duties overlap. Agree in writing who tests, who records results and who keeps the record. A typical split: the host maintains the space and its isolation, the incoming crew supplies and operates the gas monitor, and a nominated person confirms entry authority. Before work starts, all workers must be briefed on the work, risks and controls. Keep that briefing record on site with the JHA or SWMS. If the scope changes or a control's efficiency drops, work must stop. Name the person authorised to call that stop. Contractor cue: if nobody has named the tester before the lid comes off, ask then. Do not enter on an assumed handover. For the PCBU basics, see WorkSafe WA: What PCBUs and Workers Need to Know.
Gas Monitor Calibration and Bump Testing Before Entry
Once you've agreed who runs the test and who signs off, the monitor itself has to prove it's up to the job. The PCBU supplying confined space entry equipment must make sure it's suitable for its intended use, inspected and approved before use, and calibrated and maintained to manufacturer specifications.
Keep the two checks separate in your head. The bump test is the pre-entry proof that the gas monitor responds to gas and alarms correctly. Calibration is the scheduled proof that it reads true against a known concentration. Both are required as per manufacturer specifications, and our guide to gas detection equipment: bump testing and calibration explained covers the detail.
If a monitor fails either check, remove it from service immediately. Don't pop it back in the kit with a sticky note, because that monitor will find its way to a crew at 5am.
Decide and document who holds the bump test and calibration logs, where they live, and how a supervisor on the next shift verifies status before the crew kits up. Better yet, keep the monitor, its log and the tester's name together in the entry pack so the equipment record and the readings never drift apart.
Confined Space Gas Monitoring: The Pre-Entry Sequence, Step by Step
Checks and logs sorted, the test itself follows a fixed order with a named person on every line. Here's how to run confined space gas monitoring before entry.
Step 1: Confirm the space, isolation and entry authority. The nominated competent person, with the sentry present, confirms the space, verifies isolation and holds the entry authority. Say it out loud before touching the monitor.
Step 2: Bump test the monitor and record the result in front of the crew. This keeps the equipment check and the readings on one timestamp, so the two can't be quarantined from each other later.
Step 3: Test from outside, before entry. Follow the manufacturer's probe and sample line instructions, allow the instrument's minimum response time, and test at the levels where gas is likely to sit in that particular space.
Step 4: Record every result. Time, tester name, monitor serial number and location of the reading, then the nominated person signs the entry authority. No name, no record, no entry.
Step 5: Re-test after ventilation or purging. If ventilation is part of the plan, the pre-ventilation reading is not the entry reading. Run the sequence again and record the second set.
Step 6: Confirm continuous monitoring. Agree alarm set points and the action on alarm with the sentry before anyone goes in. Monitoring doesn't end with the pre-entry test; it runs for the duration of the task.
If that sequence feels like a gap in your crew's knowledge, our Confined Space & Gas Detection course covers the practical side. Next, we'll look at the paper trail that proves all this actually happened.
Documentation: The Paper Trail That Proves Ownership
Once the readings are logged, the paperwork has to stay where the work is. Under the WACHS Confined Space Procedure v1.00 (published 14 July 2025), JHAs or SWMS for entry tasks must be held at the job site while the task is underway, not filed back in the site office. Keep the minimum record set together: named tester, monitor calibration and bump test status, readings with times, signed entry authority and the pre-entry briefing record. If you need a model for a clean, usable record, see what good documentation looks like for manual handling compliance.
Use only controlled host documents. The WACHS procedure is valid only when sourced through its HealthPoint policy system; uncontrolled copies are explicitly flagged as unreliable. Good records earn their keep after an incident. Investigators will ask who tested, with what instrument, and when that instrument was last verified. If your pack cannot answer those three questions in seconds, it is paperwork theatre. The record is the evidence a duty holder did what the Code of Practice expects. Make it usable by a supervisor in seconds, not a folder for the audit.
Where Gas Testing Training Fits In
Once the records are on site, the remaining question is capability. Safety Heights and Rescue Training is a Registered Training Organisation, RTO code 52610, based in Naval Base, Perth, delivering nationally recognised training for workers, supervisors and admin staff in high-risk environments.
Match the course to the SWMS task list. Send the person running the gas monitor to gas testing training for atmospheric monitor operators. Send the crew and the sentry to confined space training. That split keeps the pre-entry sequence aligned with who actually performs each job.
Training builds competence, but it does not make someone the nominated tester for your site. That nomination is a site decision, recorded in writing in the JHA or SWMS. The business also provides shutdown emergency response services in Perth, which suits sites needing standby rescue capability rather than training alone.
Always verify any unit code against the National Training Register for the current release before relying on it, and use descriptive anchor text on internal course links.
Quick Handover Checklist for Your Next Entry
Training gives your crew the baseline. This checklist is the same-day gate.
Name the competent person in writing before the shift starts. Not a nod on the day. Put the name, position and authority in the JHA or SWMS.
Check the gas monitor's bump test and calibration status. Record both, plus the monitor serial number, so the equipment and readings match.
Run the required confined space gas monitoring sequence. Record each reading with a time, then have the nominated person sign the entry authority.
Keep the JHA or SWMS, the readings and the briefing record on site for the whole task. Not back in the office.
Brief the crew, name the sentry and name the person who can stop the job. Then enter.
If any of those five steps is missing, the entry is not ready. No gas monitor should change hands on an assumption.
Conclusion
Who owns the gas monitor before confined space entry? The answer sits in your paperwork, not in a verbal handover. Under the Work Health and Safety Act 2020 (WA) and the Work Health and Safety (General) Regulations 2022 (WA), the nominated competent person must be identified in writing. Equipment checks, monitoring sequence and entry authority all need signatures that match a name.
The good news is that strong habits are simple ones. Name the tester, verify the bump test and calibration, record every reading, and keep the paperwork on site. When those pieces line up, WorkSafe WA expectations and your crew's safety align without guesswork.
Ready to build that baseline? Ask about confined space training and shutdown emergency response services in Perth for your team. Make safety a starting point, not an afterthought.
Frequently Asked Questions
Who owns the gas monitor before a confined space entry in WA?
Ownership is defined by a named competent person, a calibrated and bump tested gas monitor, and a documented pre-entry sequence. The post says the host employer usually owns the space and the incoming crew owns the entry, and the gas test sits between them. The tester should be named in writing in the JHA or SWMS, along with their position and authority, rather than assumed.
What does the Work Health and Safety Act 2020 (WA) require before anyone tests a confined space?
The Act places a primary duty of care on every PCBU to keep workers and others safe, so far as is reasonably practicable. Specific confined space duties sit in the Work Health and Safety (General) Regulations 2022 (WA). The approved Code of Practice: Confined spaces, issued under section 274 of the Act, is enforced by WorkSafe WA and can be used as evidence of what is known about the hazard and its controls.
Who is the competent person for confined space gas testing?
The competent person is the nominated tester named in the JHA or SWMS, with a stated position and authority covering monitor selection, running the test, interpreting results and authorising entry. Competence is shown by current training, hands-on time with that specific gas monitor, and knowledge of the hazards in that particular space. A sentry, who controls entry and exit and monitors people inside, is a separate role.
What is the difference between a bump test and calibration?
A bump test is the pre-entry proof that the gas monitor responds to gas and alarms correctly. Calibration is the scheduled proof that the monitor reads true against a known concentration. Both are required as per manufacturer specifications. If a monitor fails either check, it must be removed from service immediately.
What are the steps in the pre-entry gas monitoring sequence?
The sequence is: (1) confirm the space, isolation and entry authority with the competent person and sentry present; (2) bump test the monitor and record the result in front of the crew; (3) test from outside the space before entry, following the manufacturer's instructions and testing where gas is likely to sit; (4) record every result with time, tester name, monitor serial number and location, then have the nominated person sign the entry authority; (5) re-test after any ventilation or purging; and (6) agree alarm set points and alarm actions with the sentry and confirm continuous monitoring for the task's duration.






Comments